HVAC Noise

HVAC Noise

HVAC Noise Control

Industrial Noise Control

Sound Control Solutions for Large Office Equipment


HVAC Noise Reduction

Industrial Noise Solutions

On occasion, noise levels from heating, ventilating and air-conditioning (HVAC) systems are excessive. This can be due to poor initial design, a change in the design of the space without adjusting the HVAC system, or problems relating to maintenance. These noise levels can be simply annoying or, on occasion can inhibit communications, especially in large space such as a conference or training room. Those elevated background noise levels can also interfere with the microphone pick-ups for video and teleconferencing facilities.

ASHRAE (The American Society of Heating, Refrigeration and Air-conditioning Engineers) has developed noise criteria for systems based on the space they are conditioning. These are referred to as NC levels or curves.

Sometimes it is quite obvious as to where the noise is originating, sometimes not; and sometimes there is more than one cause of the unacceptable noise level.

If the source is hard to identify at first observation, it is usually easiest to begin at the delivery end of the system and work back to the mechanical equipment.

Check the diffusers. If they are undersized or there are not enough of them, they will have an excess of air being delivered through too small an opening (or openings). That’s how we whistle: forcing a lot of air through a small opening. This excessive discharge velocity causes that “ssshhh” sound.

SOLUTIONS: Open the diffuser opening more (if it has been partially shut), reduce the volume at the volume control damper for that space if there is too much air being delivered, replace the diffuser(s) with larger one(s) or add more diffusers.

Check the ductwork. If it is rumbling it could be caused by turbulence at direction changes (elbows) or reducers. Adjustments in supply air volume or the installation of turning vanes may be the solution. If the duct is resonating (vibrating) a damping material should be considered. If you strike a bell it rings. If you hold the bell and strike it you stop its resonation (it goes “clunk”). Damping materials make ducts and other vibrating materials “go clunk.” The duct may be vibrating due to turbulence, excessive volume or the transmission of vibration from things connected to the duct – frequently the mechanical equipment itself. Duct silencers and duct liners are also options in preventing noise from traveling through the sound pipe that is your duct system.

Check the mechanical equipment (home base). Worn parts (bearings, belts), lose covers, housings and fan belt shrouds, are typical noise generators. The original vibration isolation mountings may be worn or frozen. Is there a sound absorbing/damping liner on the inside of the housing? These can be added. Under unusual conditions, it may be necessary to create an enclosure to contain the noise from the mechanical room or HVAC equipment.

Other Issues: Ductwork can provide a conduit for conversation which, in certain sensitive situations (secure government “need to know” environments, human resources, etc) can be a problem. Sound traps and duct liner can be useful. Additionally the addition of masking sound into the duct and/or the sensitive and adjacent space should be considered.

Open return vents can also provide a less inhibited route for conversation to pass between adjacent spaces. They also permit noise in the plenum to be transmitted to the occupied space below. Sound traps above the return grills will address that path.

These suggestions provide an overview and may enable you to identify the cause of a problem. Sometime the solutions are easily executed and sometime your HVAC engineer, contractor or others need to be brought in.

Contact A Representative
First & Last Name (required)


Terms of Service | Sound Management Group. All information is protected under the privacy policy of Sound Management Group. We will not share your information with any third party. Agreement to the Terms of Services gives Sound Management Group permission to keep you up-to-date via an official monthly email newsletter and add you to our mailing list.

Northeast & MidAtlantic
Virginia, Delaware, Maryland, DC, Pennsylvania, NJ, NY State, NYC, Long Island, Connecticut, Rhode Island, Massachusetts, Maine, New Hampshire. Quebec and Montreal
Contact Paul Barkman:
T: + 1 (908) 285-3419
E: paulb@soundmanagementgroup.com

Southeast Region
Mississippi, Alabama, Georgia, Missouri, Tennessee, Arkansas, Kentucky, North & South Carolina
Contact Eric Walton:
T: +1 (512) 689-4113
E: ericw@soundmanagementgroup.com

Florida, The Caribbean & Puerto Rico.
Contact Art Barkman:
T: + 1 (908) 313-4052
E: artb@soundmanagementgroup.com

South and Mountain Region
Texas, Louisiana, Colorado, Oklahoma, New Mexico, Kansas, Nebraska, Arkansas, Missouri. International
Contact Mike Barkman:
T: +1 (908) 285-3418
E: mikeb@soundmanagementgroup.com

Midwest Region
Illinois, Minnesota, Wisconsin, Iowa, Indiana, Ohio, Michigan. Toronto.
Contact Roy Bocchieri:
T: +1 (630) 995-2812
E: royb@soundmanagementgroup.com

West & Northwest Region
California, Oregon, Washington, Utah, Arizona, & Hawaii, British Columbia
Contact Keith Barkman:
T: +1 (908) 295-9027
E: keithb@soundmanagementgroup.com

West Region
Northern California, Nevada, Idaho, Wyoming, North and South Dakota
Contact Keith Barkman:
T: +1 (908) 295-9027
E: keithb@soundmanagementgroup.com